
Published: Nov 4, 2026 · Source: Instrumentation Monthly
In this Q&A, Johan Sandberg, business development manager for tank gauging at Emerson, explains why modern non-contacting radar gauges are ideally suited to LNG and LPG level measurement.
In storage tanks containing either liquefied natural gas (LNG) or liquefied petroleum gas (LPG), accurate and reliable level measurement underpins both operational and safety performance. Level data supports inventory control and custody transfer, where even small errors can translate into significant financial discrepancies because of the high value and large volume of stored product. Perhaps even more important is the need to prevent overfills.
LNG and LPG are hazardous fuels, so a spill could have severe safety and environmental consequences. International standards such as IEC 61511 therefore require certified overfill prevention systems, with level instruments as essential components. Continuous level monitoring also supports early leak detection, as a falling level in a sealed tank may be the earliest indication of a loss of containment.
Liquefied gas applications impose some of the harshest conditions encountered in process automation. LNG is stored in vast cryogenic tanks with a capacity of up to 200,000 cubic metres. This demands instruments that provide accurate measurements at a range of more than 40 metres (131 feet) while also tolerating thermal stress and resisting brittleness in cryogenic conditions. LPG presents different but equally complex challenges.
Stored either pressurised or semi-refrigerated, it can rapidly vaporise with temperature or pressure changes, generating turbulence and a vapour layer that can impact measurements. Density variations can further affect any technology dependent on buoyancy or hydrostatic principles. Also, because liquefied gas tanks are typically sealed throughout operation, instruments must have minimal maintenance requirements.
Servo gauges were long regarded as the industry standard for liquefied gas tanks. Using a wire-suspended displacer adjusted by an electric motor, they infer level from changes in wire tension. Although widely used for decades, servos have inherent limitations stemming from their mechanical complexity. Their numerous moving parts are prone to wear, leading to a mean time between failures (MTBF) that can be as short as five years, while direct contact with the product can cause contamination. Wire breakage is a regular maintenance concern, and if a displacer falls into the tank, it may pose a risk to rotating equipment. Even isolating the gauge for service carries the possibility of mechanical damage.
Furthermore, servo gauges are fundamentally influenced by product density. Variations caused by temperature or compositional changes can appear as genuine level movement, compromising accuracy. As operational expectations have tightened around accuracy, safety performance and lifecycle costs, these limitations have become increasingly significant.
Non-contacting radar – specifically frequency modulated continuous wave (FMCW) technology – has become the preferred method for level measurement in LNG and LPG tanks. These instruments emit continuous microwave signals towards the surface of the liquid and determine the level from the time delay and frequency shift of the reflected echo. Because no mechanical components contact the product, contamination and wear are eliminated.
This design results in exceptionally high availability and long service life. Non-contacting radar gauges routinely operate for 20 years or more without adjustment, with the MTBF of critical components measured in decades. Accuracy typically reaches ±0.5 mm, significantly reducing inventory uncertainty and improving custody transfer confidence.
Modern non-contacting radar level gauges can measure at distances exceeding 60 metres – supporting even the largest cryogenic tanks – and perform reliably on products with very low dielectric constants, such as LNG and LPG, where reflected echoes are naturally weaker. The Rosemount 5900S Radar Level Gauge from Emerson exemplifies this capability, with a high dynamic range and sophisticated signal processing algorithms ensuring stable and precise measurements under all conditions.
A Rosemount 5900S Radar Level Gauge from Emerson, with an added Rosemount 2051 Pressure Transmitter for use in liquefied gas tanks.
Antenna selection is critical to achieving accurate and reliable radar measurements in liquefied gas tanks. Specialised antennas are engineered to optimise transmission and reception even at low dielectric constants, withstand cryogenic temperatures, resist vapour condensation or icing, and maintain consistent performance despite changes in vapour pressure and density.
Turbulence – whether caused by filling, withdrawal or natural boiling – can disrupt the liquid surface. To mitigate this, most radar gauges in LNG and LPG tanks operate within a still-pipe. This pipe guides the radar beam, isolates it from surface agitation and provides a consistent reflection path. The result is a strong, stable echo even when there is surface movement.
Historically, some operators questioned whether vapour or high gas density above the liquid surface might affect radar accuracy. However, these concerns are unfounded. Modern non-contacting radar level gauges automatically compensate for the effects of vapour on microwave propagation speed. By using a pressure transmitter to measure vapour pressure and combining this data with information about the gas composition and temperature, a radar gauge can dynamically correct for any influence of vapour conditions on signal transmission. The result is stable, accurate measurement even as tank conditions vary.
The global installed base of non-contacting radar gauges provides strong evidence of their suitability and reliability. More than 10,000 LNG and LPG tanks worldwide now rely on radar level measurements, and in four decades of service, no Emerson radar installation has experienced reliability or safety problems due to vapour or high gas density. The design of these devices enables their availability to usually reach close to 100 per cent during their long lifespan, which helps to maximise the operational availability of tanks. In the unlikely event of a failure occurring, diagnostic software will typically identify it and take the device to a safe state.
A key differentiator of modern radar gauges is their ability to perform verification without interrupting tank operation. These devices incorporate fixed reference points – a verification pin and a reflective target – within the still-pipe. The gauge continually compares measured echoes against these known distances, enabling early detection of calibration drift, mechanical issues or signal degradation. This non-intrusive verification can be carried out online, with no need to access the tank roof or isolate instrumentation, thereby improving safety and reducing maintenance costs.
Yes, because liquefied gas storage demands instrumentation that delivers extreme accuracy, high reliability and minimal maintenance. Servo technology, although once the industry standard, now represents a legacy approach that struggles to meet modern expectations for performance and maintainability. Non-contacting FMCW radar, meanwhile, has demonstrated decades of dependable performance, providing accuracy within fractions of a millimetre and availability that approaches 100 per cent. With proven capability in cryogenic environments and the ability to verify performance online, radar technology has become the clear choice for LNG and LPG tank gauging and overfill prevention.
Read other recent instrumentation news: https://instrumentation.co.uk/category/news/
Source: Instrumentation Monthly · Original article: LNG and LPG level measurement: why choose non-contacting radar?