75 GB/s data acquisition to disk using ADQ35 digitisers

Published: Nov 17, 2026 · Source: Instrumentation Monthly

A cost-optimized solution with ADQ35, leveraging libads.Teledyne SP Devices’ ADQ3 series digitizers offer high data throughput and an SDK designed for easy application development. In this article, we present a disk streaming system that sustains 75 GB/s write throughput across 6 channels for over 50 seconds, capturing 4 TB of data. The system is built on the DPS7-PCIe platform with six ADQ35 digitisers, each acquiring at 10 GSPS (12.5 GB/s per channel). Customers use this type of system in applications such as satellite monitoring and lidar.

Low-cost consumer NVMe drives are configured in single-level cell (SLC) mode to deliver over 12.5 GB/s per drive. Combined with Teledyne SP Devices’ libads disk streaming library, which bypasses the operating system’s file system and offloads the CPU, the result is a cost-effective solution with minimal system overhead. Lower-cost setups can cost as little as 5 to 10 per cent of the price of enterprise solutions, making them worth considering if the application does not require enterprise-grade endurance.

System overview

Built on the Teledyne SP Devices DPS7-PCIe platform in a compact 4U rackmount or desktop form factor (Figure 1), the system acquires and stores data from six channels at 10 GSPS or 12 channels at 5 GSPS. Continuous recording for over 50 seconds yields a total data volume of 4 TB. The system is fully self-contained, with integrated clock generation and distribution and trigger synchronisation across all channels.

A 10 MHz clock reference generated by the clock fanout board was distributed to all digitisers. The trigger ports were connected in a daisy chain, with one digitiser configured as the master. This allows acquisition to start in sync across all digitisers.

About libads

libads is a high-performance disk streaming library designed for the ADQ3 series digitisers. It is closely integrated with the digitiser API for easy application development. The bundled examples are highly configurable, cover most use cases and can be used as a starting point for advanced applications. A custom file system reduces CPU overhead and makes stored datasets easy to identify.

The system described here uses one drive per digitiser, but the library can support multiple digitisers per drive and multiple drives per digitiser (RAID). Optional NVIDIA GPUDirect Storage support enables real-time GPU processing before storage.

The library is optimised for high throughput and low system load. Data is written asynchronously to NVMe SSDs, bypassing the operating system’s file system and caching mechanisms. This approach offloads the CPU, reducing the critical components to PCIe, storage and DRAM (or GPU). Figure 2 shows the data path. Data is written from the digitiser to DRAM buffers and then transferred to the drives for storage. The CPU handles control and monitoring.

Figure 2. The high-bandwidth data path is shown in green, and the low-bandwidth control and monitoring path is shown in red.

System component selection

The application requirements affecting component selection are listed below.

The specific component considerations for this application are described below.

The system is based on the DPS7-PCIe server-grade platform, which can be scaled to suit most applications through component selection. The detailed system specification is shown in the table below. The digitisers and NVMe drives are shown in Figure 3. The clock fanout board is shown in Figure 4, configured for PCIe slot mounting.

Figure 3. Digitisers and NVMe drives installed in the DPS7-PCIe system.

Figure 4. Teledyne SP Devices clock fanout board configured for PCIe slot mounting.

Results

The system recorded continuously across six channels for approximately 53 seconds, sustaining around 75 GB/s in total (12.5 GB/s per channel). In total, 4,020 GB were written at 74.989 GB/s. The minor deviation from 75 GB/s is due to the timer including the start-up and shutdown of the acquisition.

After recording, development functions were used to verify the integrity of the acquired data and metadata. The acquisition was repeated multiple times, with the drives formatted between runs because each run used the full capacity.

To determine the maximum sustained throughput of the drives, additional acquisitions were run with discrete records of 2,048 samples in 16-bit format. These were recorded at a sustained throughput of 75.9 GB/s, the maximum sustained throughput measured for this system configuration.

Scalability and future expansion

Disk streaming systems can be scaled to meet most requirements. The digitiser firmware options also offer a path for future upgrades. For example, a four-channel system can be built with two ADQ35 digitisers running two-channel firmware at 5 GSPS and later expanded to four ADQ35 digitisers running single-channel firmware at 10 GSPS. Available options include:

Conclusion

The disk streaming solution reduces the cost of high-speed disk streaming by using Teledyne SP Devices’ libads library and drives operating in SLC mode. As storage devices occupy fewer PCIe slots, the system can support a higher channel count per chassis.

A cost-effective disk streaming solution can be tailored to meet a wide range of requirements. We offer both complete systems and guidance for building or upgrading your own system.

Find out more about Teledyne SP Devices.

Read other recent instrumentation news: https://instrumentation.co.uk/category/news/

Source: Instrumentation Monthly · Original article: 75 GB/s data acquisition to disk using ADQ35 digitisers

Back to list

Hotline
Pre-sales: 13241121312
After-sales: 010-84932407
WeChat
WeChat ID: 13241121312
Scan to add us on WeChat
Back to top